Видео

Hi. Had this vacuum 1 year. Cleaned the filters and now it wont turn on. Just getting a red flashing light on control pad. battery is charged. Someone mentioned aligning batteries. Can you help

This video helped me so, very much. Thank you. I was going to call the guys who fix my mower to thread it but my son said I must become self sufficient. So, thanks to this video I am. 😊

gtood product for sure but if only it were this easy. took me over 30 mimutes to install one on my roof. it has a ledge under shingles. i decided easier to bllow thte leaves out ever couple of months.

What mounting screw did you use? I could not fine a #10 x 1 1/2" screw that would fit into the mounting slot on the charger. EGO should have provided those! Thanks

Thanks. I had reloaded before, but forgot about clockwise. When I did try clockwise I must have had the head closed. Watching you made me realize it, Also, I think I may end up being happier it's manual.

Thank dude! Your a life saver

Thank you❤

What if they painted it with semi gloss I’m trying match smaller spike pattern

This video was very helpful. Also I love how authentic you are

WHAT??? IT DOESN'T GO IN THE HOLES 😡😡😡😡 Thanks Dad.

Excellent instructions. Thanks.

Thanks. I knew it was easy but wanted to view a video first.

I need a video on how to remove these!

Mine will close half way super fast then go slower and not latch all the way, never thought a door would be this annoying 😂

Mine doesn’t extend when bumped.

Thanks.

Ordered a cheap plastic. Here is my comparison: Ego: Pros: rubber coating love it for durability and prevent slipping. Cons: price Generic: Pros: cheap, lightseight, Cons: cheaper in quality, not sure on long term use. Ive used lots of dewalt knock offs and had no issue i have used a milwaukee knock off and had issues on charging to full capacity Thanks for honest review God Bless T

Thanks!

Any idea how to fix a "slipping" self-propel mechanism?

I have the ST 1500SF and got the AH1530 head. It fits perfectly and took less then 5 minutes to install after watching your video. Your video was one of the best how to videos I have ever seen....short, accurate and to the point. Thanks

I’m off grid. A 30 acre mixed maple birch pine forest. It’s about 2 miles to the nearest telephone pole. So I have a pretty good solar power source. I stared with stihl and cut down a lot of trees clearing for my garden and winter heat. Often run into difficulty starting. Also no mater how careful I am I tend to spill some gas & oil. Same for the lawn mower. I hate poisoning the virgin soil. I absolutely love the ego products. Battery tech las come a long way. Clean and quiet. The string trimmers just work they wind automatically and never get tangled. For someone with a reliable power source this is the way to go. Thanks for the video.

thank you.

You save me an hour of time thank you

Very infromative and clear info. There’s a lot of debate regarding this issue here in the Philippines. But Iike what you’ve said, that’s the right thing to do and it says on the CarManual as well.

Thank you, I am a widow whom my husband treated like a princess. I had no idea about assembly of those tools. I couldn't do it without your help.

THANK YOU!!! This helped so much!!

OMG....Thank u🙏🙏🙏🤗🤗🤗

Thanks for posting this. I bought the glue a while ago but have been reluctant to use it incase I did the wrong thing and ruined the shoes. This was because the 'how to use' instructions on the back of the card are written in type so tiny that they (the instructions) might as well not be there.

Your very detail video saved my Harbor Freight Hercules 1/2" 20V Model HC92K1 drill which sold for $120. It was advertised as "comparable" to the Dewalt drill and a compatable chuck sells for $16 on Amazon that one reviewer indicated it fit Hercules. My drill's chuck would open to full width but would not tighten enough to hold any drill less that 1/4". The screw in the chuck was a Toric 15 and it turns out that it was very loose. I tighten the screw (left threads) and now it works just fine and no new chuck needed.

Try some dykes, works better and takes less time

THANK YOU!!!

But why would you break that piece? It could have been sold or given away

Love this trimmer but Hate loading it. It can take me up to a half hour to get the string through the holes everytime unless I get lucky. I have even given up after frustration and gone to do something else. I've tried going slowly, keeping the string as straight as possible, etc. Going to have to figure a better solution. I almost wish I didn't get the power load feature.

Thank you! I just did this after watching your video and swapped out my Chuck with a older drill that had burned out and it worked great now. Thank you for the content!

Very very helpful video. Thank you very much.

I needed help to actually fill up a tire. I was told to plug it in, let I fill then use it to fill tire. I’m lost and really needed help with that. It’s is not doing anything at all even after it stopped to fill the tank but there is not pressure to fill tire and I’m stuck. 😢

I cringe so much when people parked inclined without the ebrake

Thank you!

The only thing you didn't cover was usually there's an arrow on the guard indicating the direction the blade needs to be put on. Mine does not have one. It's like 10 years old and been really reliable. However, there was never any storage built into the table saw for the wrenches. Had to adjust the blade all the way down to get the new one in and the old one off after I cracked the nut. Then I had to adjust it all the way up, so I could use an adjustable wrench After finger tightening the nut. Vise grip or slender long screwdriver Perpendicular to the blade Hold the blade stationary, so you can do a final good tightening on the nut. (Model BTS12S) The only manual I could find was in french so I just had to look at the illustrations. Definitely suggest a proper open closed and wrench. Next time and we'll be making another one of those slip tools for the side opposite the nut (closest to the motor)

Mine absolutely will not come out the other side. The only differences between mine and yours is that mine has a black disc on the lid versus a green one and I can rotate mine both directions. But the string will not come out the other side.

Thanks brother !!! Perfect explanation !

I, just like everybody else, am saved by this video! Thank God some people decide to make a video of this easy handling so we don't have to fidget with the damned orange string :D

Great video! I like that it was straight to the point and you went right into it. Thank you!

Exelente video bien explicado GRACIAS

After having foot on brake pedal and shifting to neautral then engaging parking brake, do i have to put foot back on brake pedal before shifting to park or can i just shift straight to park after confirmimg parking brake was engaged on neautral?

What hunter fan is that called

Thanks!

Bought a replacement head for sf1500 2 years ago,originally sf bought with blower combo like 5 years ago. Plastic around head wore out again which you need to rewind string. Think worth buying new head again or get weed eater attachment since I have power head system already? Bought the replacement with improved floating metal disc last time. Just wonder if newer models are better built.

You should orient the teeth while installing a blade not go by the orientation of the print on the blade.

I followed your instructions BUT now my trimmer doesn't work, when I start it all the string starts coming out the hole it doesn't stay in